Non-destructive entry first, always - and we re-key Schlage, Kwikset, and Baldwin locks on the spot while you watch
You get a price before we start. It does not change when we arrive. No surprises.
Schlage Deadbolt Installation: The Marietta Owner’s Guide
Schlage deadbolt installation in Marietta typically runs $145-$280 for a standard single-cylinder replacement, including the lockset, labor, and door-prep adjustments, with same-day scheduling available. We stock Schlage B-series and Camelot/Accent collections on our trucks, along with Kwikset and Medeco alternatives. Most Marietta homeowners discover a deadbolt problem when the thumb turn spins without retracting the bolt, the key binds in humid summer months, or the strike plate no longer aligns after seasonal settling.
Which Schlage Models This Applies To
Schlage deadbolts fall into distinct product lines, and the installation requirements differ materially between them. The B60N single-cylinder and B62N double-cylinder are the Grade 2 workhorses found in most Marietta homes built 2015-2025. The Camelot and Accent series add decorative plates but use the same B-series chassis underneath. The B560P commercial-grade deadbolt, common in Town Center area retail spaces near Barrett Parkway, requires a larger 2-1/8 inch bore and a 1-inch edge bore; residential Grade 2 units tolerate a slightly smaller prep.
Identification is straightforward: remove the interior thumb turn and look for the Schlage logo stamped on the chassis, plus a small date code near the cylinder. The part number prefix tells you the series - B60 for residential single, B62 for double, B560 for commercial. We carry both OEM Schlage boxes and quality aftermarket equivalents that meet the same ANSI/BHMA Grade 2 standards. For Marietta’s older inventory, particularly homes near Whitlock Avenue with original 1990s installations, the B160 low-profile deadbolt uses a narrower faceplate that modern Schlage boxes do not include; we stock those separately. Novak Lock & Security Marietta is an independent service provider, not affiliated with Schlage.
Signs Your Schlage Deadbolt Installation Is Failing
- The thumb turn rotates but the bolt does not retract. This indicates a failed tailpiece or a cracked actuator inside the chassis. In Marietta, we see this most often on south-facing doors where summer heat and UV exposure have degraded the nylon components over six to eight years.
- The key binds, sticks, or requires jiggling to turn. Usually pin-stack wear or corrosion from humidity entering the cylinder. Georgia’s spring pollen season drives moisture into keyways; we find green oxidation on the bottom pins in roughly thirty percent of failed cylinders we remove.
- The bolt extends but does not fully seat into the strike plate. Frame settling, hinge sag, or a strike plate that was never properly mortised. In East Cobb and the Paper Mill Road corridor, clay-heavy soil movement shifts door frames seasonally.
- The deadbolt feels loose in the door, with visible wobble. The mounting screws have stripped the door substrate, or the chassis collar has cracked from overtightening during a previous installation. Hollow-core doors with particleboard fill are especially prone.
- The exterior keypad or smart lock functions intermittently. For Schlage Connect or Encode models, this points to battery corrosion, failed wire harnesses, or moisture intrusion at the ribbon cable entry point. We carry replacement gaskets for this exact failure mode.
Replacement Cost & What’s Included
| Service | Typical Range |
|---|---|
| Standard Schlage B60N single-cylinder install (existing prep) | $145 - $195 |
| Double-cylinder B62N install (existing prep) | $175 - $230 |
| Door prep modification (bore enlargement, strike mortising) | $35 - $65 |
| Smart deadbolt (Encode/Connect with Wi-Fi/Z-Wave setup) | $245 - $340 |
| Strike plate relocation or frame repair | $45 - $85 |
The range reflects three variables: the grade of lock you select, the condition of your existing door prep, and whether the strike plate needs relocation. Every quote is delivered in writing before we start, per Haven Standard Clause 1: the price on the phone is the price on the invoice. The technician is not permitted to change it at the door. Our 365-Day Done Right Promise covers all installation work, including free adjustment if the bolt drags or the strike plate needs fine-tuning after seasonal settling.
DIY or Call Us?
A homeowner can safely verify three things: whether the key turns smoothly in the cylinder with the door open, whether the bolt extends fully without binding, and whether the strike plate screws are tight. Beyond that, deadbolt installation involves precise bore alignment and strike plate mortising that determine whether the lock functions correctly and whether the door frame withstands forced entry.
We do not recommend DIY installation for double-cylinder deadbolts or smart locks, which require drilling for wire passages and proper sealing against moisture. A misaligned bore weakens the door and voids the lock’s warranty. If you’ve already purchased a Schlage deadbolt and want it installed correctly the first time, call (762) 252-5919. We’ll confirm the model number, quote a firm price, and schedule same-day service in most of Marietta.
FAQs
Grade 2 Schlage deadbolts last eight to twelve years in typical residential use, though Georgia humidity and direct sun exposure on south-facing doors can shorten that to six or seven years. We replace cylinders more often than full deadbolts. Call (762) 252-5919 if you’re unsure whether yours needs service or replacement - estimates are free.
Sometimes. A sticky cylinder can be cleaned and repinned; a loose chassis can be remounted with longer screws. But cracked actuators, worn tailpieces, and corroded smart-lock harnesses require replacement parts that often exceed the cost of a new deadbolt. We diagnose before quoting and will tell you honestly if repair is economical.
Standard replacement on a properly prepped door takes twenty to thirty minutes. Door prep modifications, strike plate relocation, or smart lock setup add thirty to sixty minutes. We quote the total time with the price, so you know what to expect before we arrive.
Yes. We carry B60N, B62N, and select Camelot/Accent finishes in satin nickel and aged bronze, plus smart lock models. If you need a specific finish or the commercial B560P, we can have it same-day from our Marietta inventory. Call (762) 252-5919 with your model number and we’ll confirm stock before dispatching.
Written by Daniel Novak, Owner & Lead Technician, Novak Lock & Security Marietta at Novak Lock & Security Marietta, serving Marietta and nearby areas.